updated 6/13/2008
1. Andrew D. Fefferman, R. O. Pohl, Alan T. Zehnder, and Jeevak M. Parpia, “Acoustic properties of amorphous silica between 1 and 500 mK,” Phys. Rev. Letters, 100, 195501 (2007).
2. Manoj Pandey, Robert B. Reichenbach, Alan T. Zehnder, Amit Lal and Harold Craighead, “Reducing anchor loss in MEMS resonators using mesa isolation,” submitted to IEEE/ASME Journal of Microelectromechanical Systems, (2008).
3. Michael Czabaj and Alan T. Zehnder, “Blistering of moisture saturated graphite/polyimide composites due to rapid heating,” submitted to Journal of Composite Materials, (2007).
4. Tuhin Sahai and Alan T. Zehnder, “Modeling of coupled dome-shaped micro-oscillators,” accepted, IEEE/ASME Journal of Microelectromechanical Systems, (2007).
5. Tuncay Alan and Alan T. Zehnder, “A Monte-Carlo simulation of the effect of surface morphology on the fracture of nanobeams,” International Journal of Fracture, 148, pp. 129-138 (2007). doi:10.1007/s10704-008-9184-8.
6. Tuncay Alan, Alan T. Zehnder, Debodhonyaa Sengupta and Melissa A. Hines, “Methyl monolayers improve the fracture strength and durability of silicon nanobeams,” Applied Physics Letters, 89, 231905, (2006).
7. Manoj Pandey, Richard Rand and Alan T. Zehnder, “Frequency locking in a forced Mathieu-van der Pol System,” accepted, Nonlinear Dynamics, (2007), doi:10.1007/s11071-007-9238-x
8. Tuhin Sahai, Rustom Bhiladvala and Alan T. Zehnder, “Thermomechanical transitions in doubly-clamped micro-oscillators,” International Journal of Non-Linear Mechanics, 42, pp. 596-607, (2007) doi:10.1016/j.ijnonlinmec.2006.12.009 .
9. Tuncay Alan, Melissa A. Hines and Alan T. Zehnder, “Effect of Surface Morphology on the Fracture Strength of Silicon Nanobeams,” Applied Physics Letters, 89, 091901 (2006).
10. Manoj Pandey, Richard Rand and Alan Zehnder, “Perturbation Analysis of Entrainment in a Micromechanical Limit Cycle Oscillator,” Communications in Nonlinear Science and Numerical Simulation, 12, pp. 1291-1301, (2007) doi:10.1016/j.cnsns.2006.01.017.
11. Peeyush Bhargava, Chun-Hua (Kathy) Chuang, Kenway Chen and Alan Zehnder, “Moisture Diffusion Properties of HFPE-II-52 Polyimide,” Journal of Applied Polymer Science, 102, pp. 3471-3479, (2006).
12. John Antonakakis, Peeyush Bhargava, Chun-Hua (Kathy) Chuang, “Linear Viscoelastic Properties of HFPE-II-52 Polyimide,” Journal of Applied Polymer Science, 100, pp. 3255-3263, (2006).
13. Peeyush Bhargava and Alan T. Zehnder, “High temperature shear strength of T650-35 / HFPE-II-52 polyimide matrix unidirectional composite,” Experimental Mechanics, 46, pp. 245-255, (2006).
14. Alan T. Zehnder, Anthony Ingraffea, Geraldine Gay, Michael Stefanone, Barry Davidson, John Dannenhoffer and Daniel Rice, “Synchronous, IP-Based, Collaborative Engineering Design Education,” invited chapter, Distance Education Issues and Challenges, Nova Press, pp 7-30, (2007).
15. Peeyush Bhargava, John Antonakakis, Christine Cunningham and Alan T. Zehnder, “Web-based virtual torsion laboratory,” Computer Applications in Engineering Education, 14, pp 1-8, (2006).
16. Manoj Pandey, Keith Aubin, Maxim Zalalutdinov , Robert Reichenbach , Alan Zehnder, Richard Rand and Harold G. Craighead, “Analysis of Frequency Locking in Optically Driven MEMS Resonators,” IEEE/ASME Journal of Microelectromechanical Systems, 15, pp. 1546-1554, (2006).
17. E. Nazaretski, R. D. Merithew, V. O. Kostroun, A. T. Zehnder, R. O. Pohl, and J. M. Parpia, “Effect of low-level radiation on the low temperature acoustic behavior of a-SiO2”, Phys. Rev. Letters, 92, pp. 245502 (2004).
18. Keith Aubin, Maxim Zalalutdinov, Tuncay Alan, Robert Reichenbach, Richard Rand, Alan Zehnder, Jeevak Parpia, and Harold Craighead, “Limit cycle oscillations in CW laser driven NEMS,” IEEE/ASME Journal of Microelectromechanical Systems, 13, pp. 1018-1026, (2004).
19. Maxim Zalalutdinov, Keith L. Aubin, Robert B. Reichenbach, Alan T. Zehnder, Brian Houston, Jeevak M. Parpia, and Harold G. Craighead, “Shell-type Micromechanical Actuator and Resonator,” Applied Physics Letters, 83, pp. 3815-3817, (2003).
20. Maxim Zalalutdinov, Keith Aubin, Manoj Pandey, Alan Zehnder, Richard Rand, Brian Houston, Jeevak Parpia, Harold Craighead, “Frequency entrainment for micromechanical oscillator,” Applied Physics Letters, 83, pp. 3281-3283, (2003).
21. D.A. Czaplewski, B. Ilic, M. Zalalutdinov, W.L.Olbricht, A.T. Zehnder, H.G. Craighead, and T.A. Michalske, “Fully encapsulated micromechanical viscometer,” IEEE/ASME Journal of Microelectromechanical Systems, 13, pp. 576-585, (2004).
22. Yu Wang, Joshua A. Henry, Alan T. Zehnder, and Melissa A. Hines, “Surface chemical control of mechanical energy dissipation in micromachined silicon devices,” J. Phys. Chem. B 107, pp. 14270-14277 (2003).
23. Alan T. Zehnder and Mark J. Viz, “Fracture Mechanics of Plates and Shells Under Combined Membrane, Bending and Twisting Moments,” Applied Mechanics Reviews, 58, pp. 37-48 (2005).
24. Kavi S. Bhalla, Alan T. Zehnder, and Xiaoyan Han, "Thermomechanics of slow stable crack growth: closing the loop between experiments and computational modeling," Engineering Fracture Mechanics, 70, pp. 2439-2458, (2003).
25. Yogesh K. Potdar, and Alan T. Zehnder, "Measurements and Simulations of Temperature and Deformation Fields in Transient Metal Cutting," Journal of Manufacturing Science and Engineering, 125, pp. 645-655, (2003).
26. Yogesh K. Potdar, and Alan T. Zehnder, "Temperature and deformation measurements in transient metal cutting," Experimental Mechanics, 44, pp. (2004).
27. Néstor Cardozo, Kavi Bhalla, Alan T. Zehnder, and Richard W. Allmendinger, "Mechanical models of fault propagation folds and comparison to the trishear kinematic model," Journal of Structural Geology, 25, pp. 1-18, (2003).
28. L. Sekaric, M. Zalalutdinov, R.B. Bhiladvala, A.T. Zehnder, J.M. Parpia, and H.G. Craighead, “Operation of nanomechanical resonant structures in air,” Applied Physics Letters, 81, pp. 2641-2643, (2002).
29. L. Sekaric, M. Zalalutdinov, S. W. Turner, A. Zehnder, J. M. Parpia and H. G. Craighead, "Nanomechanical resonant structures as tunable passive modulators of light", Applied Physics Letters, 80, pp. 3617-3619, (2002).
30. Yogesh K. Potdar, and Alan T. Zehnder, "Measurement and Simulation of Temperature and Strain Fields in Orthogonal Metal Cutting," in Metal Cutting and High Speed Machining, Daniel Dudzinski, Alain Molinari, and H. Schulz, (eds.), Kluwer Academic Publishers, (2002).
31. Ani Ural, Alan T. Zehnder, Anthony Ingraffea, "Fracture Mechanics Approach to Facesheet Delamination in Honeycomb: Measurement of Energy Release Rate of the Adhesive Bond,” Engineering Fracture Mechanics, 70, pp. 93-103, (2003).
32. T.S. Han, A. Ural, C.-S. Chen, A.T. Zehnder, A.R. Ingraffea, S.L. Billington, "Delamination Buckling and Propagation Analysis of Honeycomb Panel using Cohesive Element Approach," International Journal of Fracture, 115, pp. 101-123, (2002).
33. M. Zalalutdinov, A.T. Zehnder, A. Olkohovets, S. Turner, L. Sekaric, B. Ilic, D. Czaplewski, J.M. Parpia, and H.G. Craighead, "Auto-Parametric Optical Drive for Micromechanical Oscillators," Applied Physics Letters, 79, pp. 695-697, (2001).
34. Shujun Tang, and Alan T. Zehnder, "Nickel-Alumina Interfacial Toughness Using the Thick Foil Technique," Engineering Fracture Mechanics, 69, 701-715, (2002).
35. Alan T. Zehnder, Y.K. Potdar and Kavi Bhalla, "Plasticity Induced Heating in the Fracture and Cutting of Metals," in Thermo Mechanical Fatigue and Fracture, pp. 209-244, M.H. Aliabadi, (ed.), WIT Press, (2002), (invited review article).
36. M. Zalalutdinov, A. Olkhovets, A.T. Zehnder B. Ilic, D. Czaplewski, H. G. Craighead, and J. M. Parpia, "Optically pumped parametric amplification for MEMS oscillators," Applied Physics Letters 78, pp. 3142-3144, (2001).
37. P. Guduru, A.T. Zehnder, A.J. Rosakis, G. Ravichandran, "Dynamic, Full-Field Measurements of Crack Tip Temperatures," Engineering Fracture Mechanics, 68, pp. 1535-1556 (2001).
38. M. Zalalutdinov, B. Ilic, D. Czaplewski, A.T. Zehnder, H.G. Craighead, J.M. Parpia, "Frequency-Tunable Micromechanical Oscillator," Applied Physics Letters, 77, pp. 3287-3289, (2000).
39. Christoph L. Spiel, R.O. Pohl, and Alan T. Zehnder, "Normal Modes of A Si(100) Double-Paddle Oscillator," Review of Scientific Instruments, 72, pp. 1482-1491, (2001).
40. Alan T. Zehnder, Pradeep Guduru, Ares Rosakis, and G. Ravichandran, "Million Frames per Second Infrared Imaging System," Review of Scientific Instruments 71, pp. 3762-3768, (2000).
41. Alan T. Zehnder and Richard W. Allmendinger, "Velocity Field for the Trishear Model," Journal of Structural Geology, Vol. 22, pp. 1009-1014, (2000).
42. Alan T. Zehnder and C.-Y. Hui, “A Simple Model Relating Crack Growth Resistance to Fracture Process Parameters in Elastic-Plastic Solids,” Scripta Materialia, Vol. 42, pp. 1001-1005, (2000).
43. Alberto Zucchini, C.-Y. Hui, and Alan T. Zehnder, “Crack Tip Stress Fields for Thin Plates in Bending, Shear and Twisting: A Three Dimensional Finite Element Study,” International Journal of Fracture, 104, pp. 387-407, (2000).
44. Alan T. Zehnder, Mark J. Viz, and Yogesh K. Potdar, “Fatigue Fracture in Plates in Tension and Out-of-Plane Shear,” Fatigue and Fracture of Engineering Materials and Structures, 23, pp 403-415, (2000).
45. C.-Y. Hui, Alan T. Zehnder, and Yogesh Potdar, “Williams meets von Karman: Mode Coupling and Non-Linearity in the Fracture of Thin Plates,” International Journal of Fracture, Vol. 93, pp. 409-429, (1998).
46. Raj Kolhe, Shujun Tang, C.-Y Hui, and Alan T. Zehnder, “Cohesive Properties of Nickel-Alumina Interfaces Determined via Simulation of Ductile Bridging Experiments,” International Journal of Solids and Structures, Vol. 36, pp. 5573-5595, (1998).
47. Alan T. Zehnder, Eugene Babinsky, and Timothy Palmer, “Hybrid Method for Determining the Fraction of Plastic Work Converted to Heat,” Experimental Mechanics, Vol. 38, pp. 295-302, (1998).
48. Raj Kolhe, C.-Y. Hui, and Alan T. Zehnder, “Effects of Finite Notch Width on the Fracture of Chevron-Notched Specimens,” International Journal of Fracture, Vol. 94, pp. 189-198, (1998).
49. Alan T. Zehnder, C.-Y. Hui, and Eric D. Rodeghiero, “Chevron-Notched Toughness of Materials with Rising Fracture Resistance Curves,” Journal of the American Ceramic Society, Vol. 80, pp.1319-1322, (1997).
50. Alan T. Zehnder, Daniel V. Swenson, and Thomas Pienkos, “Polymer Reinforcements for Retarding Fatigue Crack Growth in Metals,” International Journal of Fracture, Vol. 84, pp.307-323, (1997).
51. Alan T. Zehnder, “Dfield and Pplane”, (software review) The College Mathematics Journal, Vol. 27, pp. 144-148, (1996).
52. Mark E. Thurston, and Alan T. Zehnder, “Nickel-Alumina Interfacial Fracture Toughness: Experiments and Analysis of Residual Stress Effects,” International Journal of Fracture, Vol. 76, pp. 221-241, (1996).
53. Jacob A. Kallivayalil, C.-Y. Hui and Alan T. Zehnder, “A Method for Thermo-Mechanical Analysis of Steady State Dynamic Crack Growth,” International Journal of Solids and Structures, Vol. 33, pp. 1867-1889, (1996).
54. Alan T. Zehnder and Anthony R. Ingraffea, “The Reinforcing Effect of Coverlayers on the Fatigue Life of Copper-Kapton Flex Cables,” IEEE Transactions on Components, Packaging and Manufacturing Technology Part B: Advanced Packaging, Vol. 18, pp. 704-708, (1995).
55. Mark J. Viz, Alan T. Zehnder, and John-David Bamford, “Fatigue Fracture of Thin Plates Under Tensile and Transverse Shear Stresses,” in Fracture Mechanics: 26th Volume, ASTM STP 1256, Reuter et al. (eds.) American Society for Testing and Materials, Philadelphia, PA, pp. 631-651, (1995).
56. Mark J. Viz, and Alan T. Zehnder, “Fatigue Crack Growth in 2024-T3 Aluminum Under Tensile and Transverse Shear Stresses”, in FAA/NASA International Symposium on Advanced Structural Integrity Methods for Airframe Durability and Damage Tolerance, NASA CP-3274, C. Harris, (ed.) pp. 891-910 (1994).
57. Mark E. Thurston, and Alan T. Zehnder, "Experimental Determination of Silica/Copper Interfacial Toughness," Acta Metall. Mater., Vol. 41, pp. 2985-2992, (1993).
58. Jacob A. Kallivayalil, and Alan T. Zehnder, "Measurement of the Temperature Field Induced by Dynamic Crack Growth in Beta-C Titanium," International Journal of Fracture, Vol. 66. pp. 99-120, (1994).
59. M. Viz , D. Potyondy, A. Zehnder, C. Rankin, and E. Riks, "Computation of Membrane and Bending Stress Intensity Factors for Thin, Cracked Plates," International Journal of Fracture, Vol. 72, pp. 21-38 (1995).
60. Alan T. Zehnder, and Chung-Yuen Hui, "Stress Intensity Factors for Plate Bending and Shearing Problems," Journal of Applied Mechanics, Vol. 61, pp. 719-722, (1994).
61. C.Y. Hui and Alan.T. Zehnder, "A Theory for the Fracture of Thin Plates Subjected to Bending and Twisting Moments," International Journal of Fracture, Vol. 61, pp. 211-229, (1993).
62. Alan T. Zehnder, A.C. Ramamurthy, S.J. Bless, and N.S. Brar, "Stone Impact Damage to Automotive Paint Finishes: Measurement of Temperature Rise due to Impact," International Journal of Impact Engineering, Vol. 13, pp. 133-143, (1993).
63. M.T.A. Saif, C.Y. Hui and Alan T. Zehnder, "Interface Shear Stresses Induced by Non-Uniform Heating of a Film on a Substrate," Thin Solid Films, Vol. 224, pp. 159-167, (1993).
64. Alan T. Zehnder, "A Model for the Heating due to Plastic Work," Mechanics Research Communications, Vol. 18, pp. 23-28, (1991).
65. Alan T. Zehnder and Ares J. Rosakis, "Temperature Rise at the Tip of Dynamically Propagating Cracks: Measurements Using High Speed Infrared Detectors," in Experimental Techniques in Fracture, III, J. Epstein, (ed.), VCH Publishers, pp. 125-170, (invited review article), (1993).
66. Alan T. Zehnder and Ares J. Rosakis, "Experimental Measurement of the Temperature Rise Generated During Dynamic Crack Growth in Metals," Applied Mechanics Reviews, Vol. 43, pp. S260-S265, (1990).
67. Alan T. Zehnder and Ares J. Rosakis, "On the Temperature Distribution at the Vicinity of Dynamically Propagating Cracks in 4340 Steel: Experimental Measurements using High Speed Infrared Detectors," Journal of the Mechanics and Physics of Solids, Vol. 39, pp. 385-415, (1991).
68. Alan T. Zehnder and Ares J. Rosakis, "A Note of the Use of High Speed Infrared Detectors for the Measurement of Temperature Fields at the Vicinity of Dynamically Propagating Cracks in 4340 Steel," Journal of Applied Mechanics, Vol. 59, pp. 450-452, (1992).
69. Alan T. Zehnder and Ares J. Rosakis, "Three Dimensional Effects near a Crack Tip in a Ductile Three Point Bend Specimen Part II: Experiments with Caustics and Interferometry," Journal of Applied Mechanics, Vol. 57, pp. 618-626 (1990).
70. Alan T. Zehnder, Ares J. Rosakis, and Sridhar Krishnaswamy, "Dynamic Measurement of the J-Integral in Ductile Materials: Comparison of Experimental and Numerical Techniques," International Journal of Fracture, Vol. 42, pp. 209-230, (1990).
71. Ares J. Rosakis, Alan T. Zehnder and R. Narasimhan, "Caustics by Reflection and Their Application to Elastic-Plastic and Dynamic Fracture Mechanics," Optical Engineering, Vol. 27, pp. 596-610, (1988).
72. Alan T. Zehnder and Ares J. Rosakis, "Dynamic Fracture Initiation and Propagation in 4340 Steel Under Impact Loading," International Journal of Fracture, Vol. 43, pp. 271-285, (1990).
73. Alan T. Zehnder, Ares J. Rosakis, and R. Narasimhan, "Measurement of the J Integral with Caustics: An Experimental and Numerical Investigation," in Nonlinear Fracture Mechanics: Time Dependent Fracture, ASTM STP 995, Vol. I, pp. 318-339, Saxena, Landes, Bassani, (eds.), American Society for Testing and Materials, (1989).
74. Alan T. Zehnder and Ares J. Rosakis, "A Note on the Measurement of K and J Under Small Scale Yielding Conditions Using the Method of Caustics," International Journal of Fracture, Vol. 30, pp. R43-R48, (1986).
75. Ares J. Rosakis and Alan T. Zehnder, "On the Dynamic Fracture of Structural Metals," International Journal of Fracture, Vol. 27, pp. 169-186, (1985).
76. Ares J. Rosakis and Alan T. Zehnder, "On the Method of Caustics: An Exact Analysis Based on Geometrical Optics," Journal of Elasticity, Vol. 15, pp. 347-367, (1985).
1. M. Pandey, R.B. Reichenbach, A.T. Zehnder, A. Lal and H.G. Craighead, “Anchor Loss Reduction in Resonant MEMS using MESA Structures,” Proceedings of the 2nd IEEE International Conference on Nano/Micro Engineered and Molecular Systems, IEEE NEMS 2007, 2007, p 880-885.
2. Alan T. Zehnder, and Michael W. Czabaj, “Delamination and blistering due to rapid heating of moist composites,” Proceedings of IMECE2006, 2006 ASME International Mechanical Engineering Congress and Exposition, IMECE2006-14669, (2006)
3. Tuncay Alan and Alan T. Zehnder, “Influence of Surface Properties on the Fracture of MEMS Beams,” Proceedings of the 2006 Society for Experimental Mechanics Conference, (June 2006).
4. A.T. Zehnder, P. Bhargava, and J. Antonakakis, “Characterization of HFPE-II-52 Matrix Composites,” proceedings of 2005 Society for Experimental Mechanics Conference, (2005).
5. M. Pandey, A.T. Zehnder, R.H. Rand, M. Zalalutdinov, K.L. Aubin, H.G. Craighead and J.M. Parpia, “Entrainment of NEMS Limit Cycle Oscillations,” proceedings of 2005 Society for Experimental Mechanics Conference, (2005).
6. Manoj Pandey, Richard Rand and Alan T. Zehnder, “Frequency locking in a forced Mathieu-van der Pol system,” Proceedings of DETC 2005, Long Beach, CA, (Sept. 24-28, 2005).
7. Aubin, K. L., M. Zalalutdinov, R. B. Reichenbach, B. H. Houston, A. T. Zehnder, J. M. Parpia, H. G. Craighead, “Laser annealing for high-Q MEMS resonator,” Proc. of the SPIE - The International Society for Optical Engineering 5116: pp. 531-535, (2003).
8. M. Zalalutdinov, K. Aubin, Ch. Michael, R. Reichenbach, T. Alan, A. Zehnder, B. Houston, J. Parpia, and H.Craighead, “Shell-type micromechanical oscillator,” proceedings of the SPIE Microtechnologies for the New Millenium 5116, pp. 5116: 229-36, (2003).
9. D.A. Czaplewski; Ilic, B.; Zalalutdmov, M.; Olbricht, W.L.; Zehnder, A.T.; Craighead, H.G.; Michalske, T.A.; “In-channel micromechanical plate interacting with fluid flow,” TRANSDUCERS, Solid-State Sensors, Actuators and Microsystems, 12th International Conference , Volume: 1 (2003) pp. 392 – 395.
10. B. Davidson, J. Dannenhoffer, G. Gay, a. Ingraffea, S. Jones, J-S Lee, M. Stefanone and A. Zehnder, “Facilitating effective geographically distributed engineering design teams,” proceedings of the 33rd ASEE/IEEE Frontiers in Education Conference, (2003).
11. Linlin Wang, Dieter Ast, Peeyush Bhargava, and Alan Zehnder, “Curved silicon electronics,” MRS Spring Meeting, (2003).
12. A. Zehnder, “Two Experiments in Dynamic Thermomechanics,” 2003 Society for Experimental Mechanics (SEM) Annual Conference on Experimental and Applied Mechanics, (2003).
13. M. Zalalutdinov, J. Parpia, K Aubin, H. Craighead, T. Alan, A. Zehnder, R. Rand, “Hopf bifurcation in a disk-shaped NEMS,” proceedings of the ASME Design Engineering Technical Conference, Chicago (2003).
14. B. Davidson, J. Dannenhoffer, G. Gay, A. Ingraffea, S. Jones, J.-S. Lee, M. Stefanone, and A. Zehnder, “On the use of Advanced IT Tools to Facilitate Effective, Geographically Distributed Student Design Teams,” proceedings of the 2003 American Society for Engineering Education Annual Conference & Exposition, (2003).
15. P. Bhargava, C. Cunningham, M. Tolomeo, and A. Zehnder, “Virtual Labs, Real Data for Statics and Mechanics of Materials,” proceedings of the 2003 American Society for Engineering Education Annual Conference & Exposition, (2003).
16. B.Davidson, R. Davidson, G. Gay, A. Ingraffea, M. Miller, L. Nozick, A. Zehnder, R. Sheckler, and C. Rath, "Distance design collaboration through an advanced interactive discovery environment (AIDE)," proceedings of the 2002 American Society for Engineering Education Annual Conference & Exposition, (2002).
17. M. Zalalutdinov, Lidija Sekaric, A.T. Zehnder, H.G. Craighead, and J.M. Parpia, “Light-activated Self-generation and Parametric Amplification in MEMS,” proceedings of the 2002 Society for Experimental Mechanics (SEM) Annual Conference on Experimental and Applied Mechanics, (2002).
18. Alan T. Zehnder, Y.K. Potdar, X. Deng, and C. Shet, "An Experimental and Computational Study of Temperature and Strain Fields in Metal Cutting," proceedings of Symposium on Fundamental Issues in Machining, IMECE 2001/MED-23309, ASME Manufacturing Engineering Division, New York, (2001).
19. M. Zalalutdinov, A. Olkhovets, A.T. Zehnder, B. Ilic, D. Czaplewcki, J.M. Parpia, H.G. Craighead, "Light-Induced Parametric Amplification in MEMS Oscillators," proceedings of DTIP 2001 (Design, Test, Integration and Packaging of MEMS/MOEMS), Cannes-Mandelieu, "Côte d'Azur", France, (2001).
20. M. Zalalutdinov, A.T. Zehnder, A. Olkhovets, S. Turner, L. Sekaric, B. Ilic, D. Czaplewcki, J.M. Parpia, H.G. Craighead, "Light-Activated Self-Generation and Parametric Amplification for MEMS Oscillators," proceedings of SPIE Meeting on Microfabrication, San Francisco, (2001).
21. Alan T. Zehnder, C.-Y. Hui, Yogesh Potdar, and Alberto Zucchini, “Fracture Mechanics of Thin, Cracked Plates Under Tension, Bending and out-of-plane Shear Loading,” proceedings of the Second joint NASA/FAA/DoD Conference on Aging Aircraft, C. Harris, ed., pp. 627-634, (1998).
22. Alan T. Zehnder, and A.C. Ramamurthy, “Simulation of Temperature Assisted Water Jet Erosion of Painted TPO Systems,” proceedings of TPOs in Automotive, ‘95, Executive Conference Management, Plymouth, MI, (1995).
23. Steven A. Jones, James M. Burlitch, Ersan Ustundag, Jeannie Yoo, and Alan T. Zehnder, “Nickel-Alumina Composites: In Situ Synthesis by a Displacement Reaction, and Mechanical Properties,” in Ceramic Matrix Composites - Advanced High-Temperature Structural Materials, Louden et al. (eds.), proceedings of 1994 MRS Symposium, (1995).
24. Jacob A. Kallivayalil, and Alan T. Zehnder, “Crack Tip Temperature Fields,” proceedings of the 1994 Spring Meeting of the Society for Experimental Mechanics.
25. Mark E. Thurston, and Alan T. Zehnder, “Characterization of Silica/Copper Interfacial Fracture Behavior,” in Ultrasonic Characterization and Mechanics of Interfaces, ASME AMD-Vol. 177, Rokhlin et al. (eds.), pp. 45-53, American Society of Mechanical Engineers, (1993), (invited paper).
26. Alan T. Zehnder, Mark J. Viz, and Anthony R. Ingraffea, "Fatigue Fracture in Thin Plates Subjected to Tensile and Shearing Loads: Crack Tip Fields, J Integral and Preliminary Experimental Results," Proceedings of the VII International Congress on Experimental Mechanics, pp. 44-50, Society for Experimental Mechanics, Bethel, CT, (1992).
27. Mark E. Thurston, and Alan T. Zehnder, "Mixed Mode Fracture Toughness of Silica/Copper Interfaces," Proceedings of the VII International Congress on Experimental Mechanics, pp. 1587-1593, Society for Experimental Mechanics, Bethel, CT, (1992).
28. Saif, C.Y. Hui, and Alan T. Zehnder, "Film/Substrate Stresses due to Local Heating," Proceedings of the Localized Damage 1992 Conference, Southhampton, UK, (July 1992).
29. Alan T. Zehnder, A.C. Ramamurthy, S.J. Bless, and N.S. Brar, "Temperature Rise in Automotive Paint Coatings due to Stone Impact," Polymeric Materials Science and Engineering, Proceeding of the ACS, Vol. 67, pp. 116-117, (1992).
30. Alan T. Zehnder and Jacob A. Kallivayalil, "Temperature Rise at the Tip of Dynamically Propagating Cracks," proceedings of the 1991 Spring Meeting of the Society for Experimental Mechanics, pp. 363-369.
31. Alan T. Zehnder and Jacob A. Kallivayalil, "Temperature Rise due to Dynamic Crack Growth in Beta-C Titanium," Second International Conference on Photomechanics and Speckle Metrology: Speckle Techniques, Birefringence Methods, and Applications to Solid Mechanics, Fu-Pen Chiang, Editor, Proc. SPIE 1554A, pp. 48-59 (1991).
32. Alan T. Zehnder and Ares J. Rosakis, "Temperature Fields Generated During Dynamic Crack Growth in Metals: High Resolution Measurements by Means of High Speed Infrared Sensors," in Micromechanics: Experimental Techniques, ASME AMD-Vol. 102, W.N. Sharpe, ed., pp. 179-192, presented at the ASME Winter Annual Meeting, San Francisco, (1989).
33. Alan T. Zehnder and Ares J. Rosakis, "Experimental Measurement of the Temperature Rise Generated During Dynamic Crack Growth in Metals," Engineering Science Preprints-26, presented at the 26th Annual Meeting of the Society of Engineering Science, Ann Arbor, Michigan, (1989).
34. Narasimhan, Alan T. Zehnder, and Ares J. Rosakis, "Three Dimensional Fields for a Through Crack in an Elastic-Plastic Solid: Numerical Analysis and Comparison with Interferometric Measurements," in Analytical, Numerical and Experimental Aspects of Three Dimensional Fracture Processes, ASME AMD-Vol. 91, Rosakis and Ravi-Chandar, (eds.), pp. 239-253, proceedings of the ASME/SES symposium, Berkeley, California, (1988).
35. Ares J. Rosakis, Alan T. Zehnder and R. Narasimhan, "Dynamic Measurement of the J Integral by the Optical Method of Caustics," proceedings of the 1987 Society for Experimental Mechanics Fall Conference, Savannah, Georgia, (1987).
36. Alan T. Zehnder and Ares J. Rosakis, "Dynamic Fracture Initiation and Propagation in 4340 Steel Under Impact Loading," Engineering Science Preprints-23, presented at the 23rd Annual Meeting of the Society of Engineering Science, Buffalo, New York, (1986).